Search 650Rider.com and XS650.com using Google!
|
| |
|
|
xs650 > > Custom Work: Chop, Bob, Cafe and Flattracker - Streettracker > > Cafe Racer > > Honda CB 360 Master Cylinder ON A XS650? |
---|
Honda CB 360 Master Cylinder ON A XS650?
|
Author |
Message |
xscaferacer Full Member
Joined: Jan 29, 2007 Posts: 35
|
Posted: January 29, 2007, 9:36 pm Post subject: Honda CB 360 Master Cylinder ON A XS650? |
|
Is it possible to put a Honda CB 360 master on a XS650 brake system? I know there is a conversion and ratio chart program or site for brake master's that will tell you what master's you can inter-change. I can't find it or really know the info on my XS master with out pulling it apart. Has anyone done this conversion or have any advice? Yes I know it's a crap Honda part, but they look so sweet all polished up.
|
|
Back to top |
|
|
stewart New Member
Joined: Jan 04, 2007 Posts: 1 Location: scotland
|
Posted: January 30, 2007, 3:26 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
what you have to think about is, how big was the pistons the
mastercylinder used to move, compaired to what you want it
to move now. Will the fluid displacement be enough
|
|
Back to top |
|
|
beys Full Member
Joined: Jan 02, 2007 Posts: 108 Location: Southern Bavaria, Germany
|
Posted: January 30, 2007, 4:46 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
stock master cylinder on the XS 650 is 14mm for single disc and 11/16'' for dual disc. Check the Honda cylinder, the diameter should be marked on it.
I would not go smaller than 14mm for the dual and 1/2'' for the single because of overbraking. Fluid displacement will be enough in any case.
_________________ beys
greets from the Simssee
Z TS 250/1 with sidecar '77
XS 650 Euro 447 Standard '80,
XT 500 '81
XS 650 US 5V4 Heritage '82 |
|
Back to top |
|
|
xscaferacer Full Member
Joined: Jan 29, 2007 Posts: 35
|
Posted: January 30, 2007, 6:54 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
It has N11 stamped in it, is that the mm?
|
|
Back to top |
|
|
beys Full Member
Joined: Jan 02, 2007 Posts: 108 Location: Southern Bavaria, Germany
|
Posted: January 31, 2007, 3:29 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
xscaferacer wrote: |
It has N11 stamped in it, is that the mm? |
maybe, but seems pretty small. Can you take it apart to mesure it?. Or, if you have a single disc, you can try it on the bike, but take care of overbraking! On a dual disc Iwouldn't try it at all!
_________________ beys
greets from the Simssee
Z TS 250/1 with sidecar '77
XS 650 Euro 447 Standard '80,
XT 500 '81
XS 650 US 5V4 Heritage '82 |
|
Back to top |
|
|
MattQ New Member
Joined: Jan 05, 2007 Posts: 6 Location: Detroit, MI
|
Posted: January 31, 2007, 4:33 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
I am planning on going to an 11mm bore master cylinder and then bolting it up to my single (1981) caliper. (11mm M/Cs are available from 650 Central and MikesXS.) It is my undestanding that this will provide a "two finger" brake system. I'll let you know how it works out.
att Q.
_________________ ------------------
97 BMW R850 R
81 XS 650
73 CL 350 |
|
Back to top |
|
|
xscaferacer Full Member
Joined: Jan 29, 2007 Posts: 35
|
Posted: February 8, 2007, 1:25 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
Killer man, Im giving it a go also, I tell ya in spring if it works too.
|
|
Back to top |
|
|
XSKID Full Member
Joined: Feb 20, 2007 Posts: 58 Location: Wisconsin (Mad. area)
|
Posted: February 20, 2007, 4:38 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
I know this thread is kinda dead, but, I happen to have a 75' CB360T brake Master Cyl. on my 77' XS650. I had to put a banjo bolt into it that had a brake light switch integrated into it.
It works, but it's kinda weak compared to the force of a factory unit.
Hope this helps,
Ben
|
|
Back to top |
|
|
Darkdruid New Member
Joined: May 19, 2007 Posts: 8 Location: England
|
Posted: June 5, 2007, 4:38 pm Post subject: Re: Honda CB 360 Master Cylinder ON A XS650? |
|
I have a Bandit 600 master cylinder fitted to my XS Special and it works very well. Definitely an improvement on the original that is fitted to my Special II!
|
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You can download files in this forum
|
|
|
|
|
Check out the new Honda CB750 Forum at CB750.com! A site dedicated to the great Honda SOHC and DOHC CB750.
Check out the new Yamaha XS400 Forum at XS400.com!
Yamaha xs650
xs650, xs, 650, forum, links, chopper, custom, yamaha, parts, forum, info,
information, bb, bulletin board, XS650 650Rider, Free Unrestricted xs650
forum, Personal photo albums, Post images in Forum, News columns, Daily blog,
Links, Event calendar, Information for Yamaha XS650
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
|
|