Search 650Rider.com and XS650.com using Google!
|
| |
|
|
xs650 > > Stock Bikes > > Original Equipment Restoration Projects > > clutch problems help needed |
---|
clutch problems help needed
|
Author |
Message |
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 28, 2009, 8:32 pm Post subject: clutch problems help needed |
|
k,,i just got a 78 650 xs,,so it wouldnt start been sitting a while,,i did the new starter gear repair kit and and did new plugs ect and it fired right up,runs good ,,my problem now is the i pull the clutch lever and nothing really happens,,i dont rem it being this way when i brought it home,,,could i have done somethin wrong when i was puting the clutch basket back in after the doig the new starter gear? when i pull the clutch lever the cable will pull the metal piece of the cable end up and when i push it back out the cable comes out the end of the adjuster on the lever,,its like somethin is in a bind or the cable is seased,,but i can hold the calbele and it seems to move freely,,any ideas are greatly appreaciated.....
|
|
Back to top |
|
|
jayel 650Rider Supporter
Joined: Apr 16, 2006 Posts: 3417 Location: SE Iowa 1974 TX650A
|
Posted: July 28, 2009, 8:35 pm Post subject: Re: clutch problems help needed |
|
sounds like the bottom end of the cable isn't hooked up
_________________ all it takes is time and money -- Where are we going and why are we in this hand basket? |
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 28, 2009, 8:37 pm Post subject: Re: clutch problems help needed |
|
is there anything i could have done wrong when putting the basket back on when i did the starter gear? i just seen a forum where the pressure plate had a certain place to line back up,,not sure i did that? but i marked it the way it came off i thought
|
|
Back to top |
|
|
Stonecold2491 Full Member
Joined: Jul 25, 2009 Posts: 14 Location: Kingsport ,Tennessee U.S.A.
|
Posted: July 28, 2009, 8:46 pm Post subject: Re: clutch problems help needed |
|
You can remove the 1 and 1/2 inch circular cover on the gearshift side of the case and pull the clutch lever to see if the eccentric is moving with pull of the clutch lever , if not the cable is loose inside or broken . To hook cable back up you need to remove the gearshift and side cover. There is a link to a repair manual in the vault section on here. Lots of good info in there.
_________________ Those were the good ole days when I wasn't good Nor Old |
|
Back to top |
|
|
nj1639 Full Member
Joined: Aug 22, 2007 Posts: 839 Location: Switzerland County, Indiana
|
Posted: July 28, 2009, 8:48 pm Post subject: Re: clutch problems help needed |
|
Lose the ball bearing in the worm gear?
_________________ "Go ahead, turn the damn power and water off, I'm ready!
'83 xs650sk
www.650rider.com/index...pic&t=5392 |
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 28, 2009, 9:34 pm Post subject: Re: clutch problems help needed |
|
ok ill check that out,,,i dont rem seeing a ball bearing when i took it apart,,,hmmm
|
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 28, 2009, 9:45 pm Post subject: Re: clutch problems help needed |
|
i just orderd a clymer manual maybe that will help me out some,,,im gona take the right side apart again and see if i have the alighment holes lined up right,,not sure if that makes a difference or what,,then ill do the right side cover to see what i can find
|
|
Back to top |
|
|
650skull Support Staff
Joined: Jul 19, 2007 Posts: 1186
|
Posted: July 29, 2009, 3:13 am Post subject: Re: clutch problems help needed |
|
Hello to you to ! I guess this is a welcome,
Have you had a good look through the site before jumping into questions If you look in the Vault under "Manual -- Parts List" and you can download a manual and look up parts through Biker net. and that will give you an exploded view of different parts + part no's This will help you to relate to any answers and help with your questions
|
|
Back to top |
|
|
jimmythetrucker Full Member
Joined: Mar 12, 2008 Posts: 1283
|
Posted: July 29, 2009, 4:43 am Post subject: Re: clutch problems help needed |
|
When you got everything put back together, did you have any parts left over?
|
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 29, 2009, 4:54 am Post subject: Re: clutch problems help needed |
|
no parts left over nope,,, i cant seem to find a picture of where the ball bearing goes thou
|
|
Back to top |
|
|
Joseph Full Member
Joined: May 22, 2007 Posts: 767 Location: NY
|
Posted: July 29, 2009, 7:19 am Post subject: Re: clutch problems help needed |
|
Did you look under the left adjuster cover to see that the cable is attached to something? As mentioned previously
_________________ Joeymountain
1980sg |
|
Back to top |
|
|
nj1639 Full Member
Joined: Aug 22, 2007 Posts: 839 Location: Switzerland County, Indiana
|
Posted: July 29, 2009, 7:57 am Post subject: Re: clutch problems help needed |
|
There's a ball bearing where the worm gear meets the clutch pushrod. It's pressed into the back of the worm gear and easily lost if you take the left side cover off. There's another one located after the clutch pushrod too.
On reassembly I greased the worm gear ball bearing to make sure it stays in place. Dirt floor mechanic here and things can get lost easily, or stolen and et by the damn chickens! HA!
_________________ "Go ahead, turn the damn power and water off, I'm ready!
'83 xs650sk
www.650rider.com/index...pic&t=5392 |
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 29, 2009, 6:30 pm Post subject: Re: clutch problems help needed |
|
too the left side cover off today and the right side back off ,,,all the pieces are there and slides back and forth easily with the clutch off,,,the cable is hooked up also,,,when i put the clutch back on i think i mut be doing somethin wrong,,cause it seems really solid and the rod wont slide back and forth anymore,,,is there soposed to be any slack in the basket when you get it back together,,,ther is a small gap at the back of the disk pack,,and i can move the basket back and forth some with my hands,,,,im deff a newby on clutch setups,,,i cant really tell whats soposed to be going on here...
|
|
Back to top |
|
|
pamcopete 650Rider Supporter
Joined: Oct 10, 2008 Posts: 875 Location: South Carolina
|
Posted: July 29, 2009, 6:45 pm Post subject: Re: clutch problems help needed |
|
hilomx6
Check this link for an important clutch aligment issue:
www.650motorcycles.com...mbly1.html
_________________ Ride.Enjoy.Life is simple |
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 29, 2009, 6:47 pm Post subject: Re: clutch problems help needed |
|
i got the two marks lined up right,,,id there anything else that has to lign up as far as when you put the clutch on the shaft?
|
|
Back to top |
|
|
Retiredgentleman 650Rider Supporter
Joined: Mar 03, 2007 Posts: 2258 Location: Calgary, Alberta 1978 XS650 SE
|
Posted: July 29, 2009, 8:27 pm Post subject: Re: clutch problems help needed |
|
hilomx6;
Here's a drawing of how your clutch should be assembled. Do you have all of these in place?
_________________ Accel Coil, Pamco Ignition, Heiden Oil Filter/Cooler, VR-115 Regulator, Double Bridge Rectifier, 17/33 gearing, 55 mpg |
|
Back to top |
|
|
hilomx6 New Member
Joined: Jul 29, 2009 Posts: 8 Location: tn
|
Posted: July 29, 2009, 8:32 pm Post subject: Re: clutch problems help needed |
|
yea everything is there,,its sorta hard to slide on the shaft at the point where the gears are,,the basket slides on back and lines up with the gears fine then after a little wiggling the plates and stuff will go on back,,but they leave about a 1/4 of gap at the back of the basket and wont go any further.. wish i had looked at it better when i took it apart to see if the gap was there.
|
|
Back to top |
|
|
Retiredgentleman 650Rider Supporter
Joined: Mar 03, 2007 Posts: 2258 Location: Calgary, Alberta 1978 XS650 SE
|
Posted: July 29, 2009, 8:47 pm Post subject: Re: clutch problems help needed |
|
Can you show us a picture of where this gap is?
_________________ Accel Coil, Pamco Ignition, Heiden Oil Filter/Cooler, VR-115 Regulator, Double Bridge Rectifier, 17/33 gearing, 55 mpg |
|
Back to top |
|
|
gordo 650Rider Supporter
Joined: Oct 09, 2008 Posts: 559 Location: CT.U.S.A.
|
Posted: July 29, 2009, 9:16 pm Post subject: Re: clutch problems help needed |
|
How many fiber disc's, and how many steel disc's? A '78 should have 7 fiber and 6 steel.Also check the alighnment of the push rod seat to the clutch basket. Reassemle the left side cover,adjust the worm gear until there is no slack, then back off about 1/8 to 1/4 turn. Watch the right side clutch area when using the lever, it should be moving. I' m thinking your worm gear area is the problem area. I replaced my pushrod's with the long one from Mike's last year, and once I got the adjustment on the worm gear right, all's well. The order of the pushrod part's is a ball bearing in the worm gear itself, the short pushrod, another ball bearing, the longer pushrod, another ball bearing at the clutch throwout rod. The rod that pushes the clutch basket.
_________________ '80 G, |
|
Back to top |
|
|
|
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum You cannot attach files in this forum You cannot download files in this forum
|
|
|
|
|
Check out the new Honda CB750 Forum at CB750.com! A site dedicated to the great Honda SOHC and DOHC CB750.
Check out the new Yamaha XS400 Forum at XS400.com!
Yamaha xs650
xs650, xs, 650, forum, links, chopper, custom, yamaha, parts, forum, info,
information, bb, bulletin board, XS650 650Rider, Free Unrestricted xs650
forum, Personal photo albums, Post images in Forum, News columns, Daily blog,
Links, Event calendar, Information for Yamaha XS650
Interactive software released under GNU GPL,
Code Credits,
Privacy Policy
|
|