Search found 45 matches

Could the stator assembly resistance test good and the assembly still be bad? I don't think I'm getting the 11 volts ac out of it.

I built the reg/rec with radio shack rec's and a chrysler reg. I wired ground from one rec to the other and from there straight to battery ground.

The regulator/rec I built had a rubber coating on it that I filed off where the bolts connect it to the frame. I checked earth groung on the regulator by just randomly scraping of some of the coating ...

There are no wires where the coils were. This bike has the least amount of wiring possible and I can't believe I can't figure it out. The one guy close that has a shop and I thought might help said he ...

Well, put all new connectors from mikes and rewired AGAIN and no change. What the hell is going on? The bike has a pamco ignition on it and I remember the guy saying he didn't put something back on wh ...

Thanks for the reply Mudd! I thought about this very thing, but might not have enough room. May have to explore this option a little more. Might be able to use very small allthread. Dont know if I can ...

That's kind of what I was thinking. I am in the process of replacing the old connectors with new from mike's and making a neat and tidy wiring harness. Hoping this will cure my problem. Had some other ...

Might work. Trying to rewire my bike to get it to charge and figured I would throw that out there while i was brainstorming. Thanks for the quick reply. Kind of scared that I will start it up and have ...

Anyone have any ideas on a battery strap I can make and use on my bike? It's the fake oil tank/battery box that's welded to the frame. Battery is just rattling around in there. I keep stuffing foam on ...

Well, I measured everything I have in the garage that I could get my hands on quickly. Hope you can follow this:

Keep in mind I have about .5 ohm drop red to black on the meter

Rotor resistance
...

Sorry I'm getting people so excited. Not really trying to. I agree on the starting over bit. I will completely start from scratch and will inform in one post as to what I find out. If you guys don't m ...

It's got a custom fake oil tank/battery tray welded under the seat that the rec/reg is bolted to. The ground wire from the reg/rec is connected to battery negative and the battery is grounded to the f ...

Get no output. That's when I tested the green brush to ground while the motor was running.

Did the Radio Shack mod and that's when I finally got the slap. Have battery voltage from right brush to ground and from left brush to ground but can't seem to get it across the brushes with just the ...

I will have to look at the model number when I get off in the morning. It's one for a 1975 Chrysler Cordoba. When I stated that I grounded the green brush I did it while the bike was running and got n ...

Found the diagram that I was trying to explain

Is this what I am understanding?
3 whites to 3 whites on the reg/rec
black wire in the stator harness to ground on frame or battery
green wire to reg/rec green
new wire ran from fused 12 volts alo ...

Let me clarify a little bit. I have simple wiring. I hooked to the black wire right after the plug coming from the stator assembly to get my 12+ volts thinking that was the black brush wire. Do I need ...

Well, let me throw this at you. Since I have "ungrounded" the right brush with the nylon screws, do I have to physically run a new wire to that brush and use the black wire in the harness as a ground? ...

Have done that and it has a 10 amp fuse that's good inline.

Meter shows .5 ohms when touching leads together. When I test slip rings I get a reading of 6 ohms. That's a cummulative total of 5.5 ohms. When I test the resistance of the stator assembly from white ...

Forgot to mention that I grounded the green brush and no change. I have another good stator assembly that tests pretty close to the one that's on it and it made no change either.

Well, been working on it again today. Retired, I have had this meter for years and have used it on countless projects so I trust it. With the new reg/rec combo with the chrysler regulator and radio sh ...

Thanks xsleo. Got fed up and finally built the one like you have. I haven't been able to run it yet because it was about 2 am when I finished. I finally have the magnetic field and a whole bunch of sl ...

What Happened to 650rider.com?

Yamaha xs650